• Quotations for a service-How hard can it be?

    yosemite_sam2-1-1[1]

    Is it me? Is my French so bad? Are dealers down here really so busy with winter coming that they don’t need work coming into their workshops to keep them going? Here’s the story.

    A week ago I decided that to try and make my K1300GT look a more attractive proposition as a purchase, I’d need to get the 90,000 service done before I advertised it for sale. I duly sent an email to three local BMW dealers asking for a quote for this service, which I know is likely to be at least €500 as it’s a major service where the valve clearances are checked. Here is the convoluted story of how this simple request fared in the wonderland that is BMW service .

     

    We start with a positive note as Dealer #1 replied to my enquiry the next day with a quote which was in line with my expectations at €464, but when I looked at it in detail I realised that most of the work quoted for had been done very recently at the 80,000 service (done late at 83,000), and that the radiator purge and refilling with new antifreeze had been done in July this year at 88,000 when I’d had a problem with it overheating. Not wanting to pay out again for work done quite recently, and given I’m selling it, I wrote back the following day with full details of the work done, and asked if they would give me a revised quote, but ONLY for work that they considered necessary, given the proximity and timing of the previous jobs and the fact I was going to be selling it. I guess I expected that they would drop the brake fluid and antifreeze, and maybe even the oil change, leaving the plugs and valve clearances, but still, they’re the experts, I figured they’d know best which elements were critical?

    A simple enough request you would think, but it then went deathly quiet and after hearing nothing for a week, I went back to them asking if they were going to reply or should I consider their silence an expression of their disinterest and that I should take my bike elsewhere? This elicited a response, but not in the form of the quote I was expecting, but a demand that I send them copies of the previous work I had done so that they could prepare an accurate quote. I sent these by return, but wondered why it was strictly necessary to do so, given that they had already had the same information in writing a week earlier!

    Expecting a reply that afternoon, guess what, I didn’t get one, so I chased again, and received a new quote, this time for €628!!!!  So after 9 days I’d now got a quote that had increased by €164 +35% over the original, which only differed from the first quote by definition of the exclusion of the brake fluid change, but now contained five jobs which had increased in price, the oil by +70%, and the addition of four items not even detailed in the original quotation.

    I wrote back telling them this quote was a joke and how was it possible that the original quote had been so inaccurate? I was left seriously unimpressed when I was informed that the original quote had been done by somebody else and contained errors and omissions, no kidding!!! It seems that I was expected to just suck it up and accept that the previous quote had been worthless, and that I shouldn’t balk at having to pay 35% more because they can’t quote correctly.

    I gave them one last chance, and asked for a quote for valve clearances and plugs only, and ended up with a price of €403, plus €50 for a loan bike, which incidently had previously been quoted as being €25. Unbelieveable. The words piss up in a brewery spring to mind.

     

    So would Dealer #2 be any better? The request for a quote was sent on the same day as to Dealer #1 . They replied two days later advising that their service manager wasn’t there and that they would reply at the end of the week. I then sent them the same mail I’d sent to the other dealer explaining about the prior work I’d had done, the fact I was selling it and asked if they would send a quote allowing for these items. I  received their confirmation back immediately that when their service manager came back he would quote allowing for these issues. Looks like they might be a bit more on the ball?

    Of course it turns out I was to be disappointed again, so the following week having not received any quote and knowing the service manager was back, I chased again and received a reply which apologised for the delay, but then asked what bike the work was required for? They also wanted a copy of the carte grise (registration document) so that they could quote correctly.

    In a bid to expedite the receipt of a quote I sent copies of the previous service invoices and the carte grise along with a note stating that the work was required for a BMW K1300GT, as per the heading of my previous two emails!!!!

    Finally, 8 days after my initial enquiry I received a quote for €571, which was €107 more than the original quote from Dealer #1, and they hadn’t removed any of the options I’d thought they might. Admittedly they had included an air filter, which to be fair I forgot to tell them wasn’t required, so this reduced the additional amount to +€62, although this appeared to be the cost of two joints(?) which had been omitted from the initial quote from  Dealer #1(but which subsequently were added to their revised quote). The big issue with the quote, apart from the price, was that they were unable to offer a courtesy bike and wanted mine the night before so that they could work on a cold engine. This is impractical and adds substantial costs and time as I’d then need to make multiple trips there and back by both car and bike to get the work done.

    In desperation I asked for a quote for the valve check and plug change only, but as of this post I’ve not had their offer.

    Wondering if all BMW dealers are so poor I tried to cover all bases by sending the same request to a third dealer (#3). This is probably the biggest of the three but is an hour and a half away. Their reply? After several days they asked to see copies of the last invoices of work done, so I decided to make it really simple and rather than send copies of the invoices I just asked that they quote for the valve clearance check and replacing the plugs, how difficult can that be? Two days later they came back asking for a copy of the carte grise. I GIVE UP!

    I hadn’t realised that asking for a quote was so difficult. I hadn’t expected that the first quote I received would have comprised so many errors that it wasn’t worth the paper it was sent on. It’s mildly insulting and shows inattention to detail when a dealer replies with an incorrect spelling of my name. It’s even worse when they ask what bike I want serviced when it is clearly indicated at the head of emails addressed to them; and asking for copies of registration documents to establish the bike model details days after an initial enquiry had been made when it should have been their first question? Professional, I think not!. Frankly it’s an appalling indictment of BMW service, and clearly if three dealers are showing the same ineptitude and delay in responding, it’s not an isolated incident.

    I’d write to the dealer CEO of each establishment to complain but frankly I can’t be bothered, and I’ve pretty much lost all interest in BMW. Shame, as it’s been a good bike with the odd fault, but BMW can say goodbye to another long term owner. I imagine they think there will be loads along to replace me, but I wonder how many others have given up too?

     

    PS- If you’re wondering what I did in the end? I decided to discount the price of the bike and let the next guy run the gamut of inefficiencies of BMW and their weird and wonderful world of customer service.


  • Holiday

    September saw our annual pilgrimage to Canada, so here are a few pictures to share with those who may not have been to the land of lakes and trees.

    Heading out of Calgary we saw lots of smoke as a forest fire was raging. It’s a perennial problem over there with so many trees and dry weather.

    p1060157

    p1060159

    Several hours further south and a few days later, no fires here, with low clouds over the surrounding mountains dulling this mid morning picture.

    p1060162

    On a days outing you get to see so many lakes and trees that they all seem to merge into one although this one was nice and stretched for miles.

    p1060165

    Further downstream on the same river, the first area with housing for half an hour. Spaces are big in  Canada and unless you’re living in a city habitation can be few and far between

    p1060170

    p1060171

    We stopped for breakfast at this cafe with it’s humourous parking sign below

    p1060178

    p1060177

    On the way back we came over the brow of a small hill and saw a brown bear at the side of the road. Crossing over I parked up and gently reversed to take a picture but it was spooked by a BMW RT which was following us and disappeared before I could take its picture.

    Here’s a signpost segment of pics.

    Got to love Canadians sense of humour. Don’t stray onto this guys land!

    p1060181

    The signage is so different in Canada to what we’re used to in the UK or Europe. Not sure the average European would do too well if he was told head East or West?

    p1060185

     

     

    p1060188

    p1060186

    p1060187

    I usually end up doing some work for my keep, you would not believe the effort and time involved to cut and move these 31 logs back to the wood shed to be cut down into boiler sized pieces.

    Crossing one of the fields to get to the woods I saw movement in the long grass ahead and something moved quickly away from me. I spotted brown hair and pointed ears and at foirst thought it must have been a coyote as we;d seen them there the previous year, but thinking back now, I’m convinced it was a bear cub, although if it was, I’d perhaps have been a bit more worried about where its mother was!

    p1060190

    We cut another 20 or so logs a couple of days later and once they were all chopped to size created they only filled a small part of the wood store (light coloured pieces)

    p1060192

    Heading home we were fortunate to finally see some Elk. In 6 visits to Canada we’ve been fortunate to see bears, mountain sheep, and eagles, but Elk and Moose have been conspicuously absent, and today, apart from seeing this group by the road side, later on we also saw another herd up on the hilltops. Pictures aren’t the greatest as it was pouring with rain but we had to stop to prove we’d seen them.

    p1060197

    p1060198

    p1060203

    p1060207

    It took the best part of a week to get over the jetlag once we’d got home but yet again we’d had a great trip, albeit a very long one!


  • MV Zagato

    I’ve had a soft spot for MV’s since I rode one of the original F4’s back in 2002. Like everyone I was blown away by the stunning design, the sound from tghe four tail pipes, and the blood red/silver colour is such a great combination and looks amazing. Talking of which, take a look at this Zagato version of the bike. A futuristic take on an already beautiful design, just need umpteem thousands to buy one!

    MV-agusta-f4z-zagato-2016-motofire-600x544

    mv-agusta-f4z


  • Triumph Speedmaster

    yosemite_sam2-1-1[1]

     

     

     

     

    triumph logo

     

     

    Every now and again I toy with the idea of riding something other than my K1300GT which has now just passed the 90,000km milestone. I bought it intending to run it long term and i’ve already had it 7 years so far, but that shouldn’t preclude me from trying other bikes, should it?

    Sometimes I think the GT is a little large for the smaller roads I’m riding these days, and as I’m not doing long distance touring the thought of something smaller and lighter has some appeal, but would this new machine be a GT replacement, or a third bike to accompany the R1 trackbike? Hmm.

    Recently someone locally was advertising a Triumph Speedmaster, and I wondered if a feet forward slower machine might suit my needs, so what else was there to do other than to go and try it?

    TBH, I’ve not been too impressed with the Triumphs I’ve ridden to date. The first, a 1050 Sprint was, I thought, a very poor VFR800 copy, with soggy suspension and less than impressive engine performance for its capacity. The next model I tried was a friends 675, which initially I was unsure about, but once the suspension had been tuned to suit my weight it was transformed and I became a massive fan. It was, and probably remains, the best handling bike I’ve ever ridden. Number 3 was a Daytona 955 which I hated everything about. The steering was heavy, I found it hard to turn, the engine didn’t win me over with its supposedly charismatic sound and nature, and to add insult to injury, the chain came off, and all this within a mile of the bike shop I was testing it from. So with a chequered history, how would the Speedmaster fare? Read on.

     

    triumph

    This particular bike was the early 2004 790cc model rather than the 865cc cpacity which came on the following years model. With only 53.1bhp from its carburetted engine and a top speed of 103mph, clearly there was going to be quite a performance deficit compared to the GT, but hey, nothing to say it wouldn’t be a blast.

    Initial checks brought a smile as I surveyed the petrol stopcock, steering lock, and cable operated clutch. The petrol cap was non locking, and the ignition key was located below the seat behind your left leg. These “old world” details brought back some fond memories of my early bike ownership from the 70’s.

    Sue was horrified to see the perch she was going to be asked to sit on, and without the safety of a top box to lean against, she had to hold on tight as we set off on this new “old” riding experience. The clutch engaged first gear smoothly and quietly compared to the usual clunk of the GT, and it never ceases to amaze me how nicely chain driven bikes change gear vs the shaft on my BMW.  The first thing that immediately required attention and rapid adaptation to was the seating position. The Speedmaster is a cruiser style bike with its footpegs placed forward towards the front wheel. Whilst this is a surprisingly comfortable and natural feeling position once moving, it leads to some panic searching for the pegs when pulling away from junctions, as feet instinctively drop to the position you’re used to finding them in, only to realise they’re not there!

    The engine accelerates quite smoothly but not with any massive urge, as you’d expect though given the relatively low power output. Gears continued to mesh smoothly but I found myself hitting the rev limiter a few times before realising I’d not been using all of the 5 gears, which just goes to show how reliant I’ve become on the gear shift indicator on my bike, and how much concentration I was using on other things. I have to say that although the speedo is very clear and shows both mph and kph (UK import), I found myself searching for the neutral light, as it’s location isn’t in the speedo in your immediate line of vision, but instead is located on the petrol tank. I missed not having a tacho, and am ashamed to say I only realised there was one when I uploaded this picture of the tank mounted instruments and saw the rather large one dominating the head of the tank. How could you not see it you’re doubtless asking??? If I had then I’d have avoided hitting the rev limiter, oops!

    speedmaster dials

    The handling seemed to be adversely affected by having a pillion, as it seemed very wallowy at the rear. Doubtless this was because we hadn’t firmed up the twin rear shocks, and in combination with a rear tyre that felt underinflated, was giving a feeling from the steering that it was quite light. You’re not massively concious of the fact the wheel seems to be raked quite some way away from you, and to be fair it turned into bends well enough for the pretty low speeds I was riding at, but I wouldn’t have felt comfortable riding too much faster without some changes being made to both tyre and shocks.

    On the subject of comfort, we both got back after the ride complaining of back ache. The ultra low seat height forces a slightly hunched position for the rider, and Sue was really unhappy clinging on and being bounced around on the soft rear suspension.

    The nearest thing to this style of bike I’ve ridden before was a Yamaha Virago back in the 90’s, so it was interesting to try something new and different after so many years. Getting back on the GT afterwards highlighted the differences between the two styles of bike with even greater clarity, the GT feeling positively scalpel like in comparison, not something you’d ever expect to say about a 285kg behemoth, but sittting on rather than in the seat, as you do on the Triumph, really does massively affect the whole feel of the bike.

    You’ll have gathered by now I didn’t buy it, but it was an interesting experience, and if you don’t try you’ll never know eh? Maybe there’s something out there to tempt me but at the moment there are only two bikes that might interest me, the Yamaha MT-09 Tracer and the Kawasaki Z1000SX, but the Kwak allegedly has slightly strange handling and I imagine will feel a bit manic in its power delivery, and be similar to the BMW S1000XR I test rode a few months ago.  Still, no rush, after 7 years waiting a few more days, or months won’t hurt!

     


  • Something different-a ride I’m not leading!

    yosemite_sam2-1-1[1]

     

    Variety is the spice of life so they say, but when it comes to riding, planning routes and setting destinations, there’s been very little variety involved as it’s generally me that does it. There have been the odd exceptions, when Karel lived in Geneva he led me round most of the high cols in Switzerland, but once he’d moved to the US I took over the tour leader mantle, and other than a couple of runs where Andy has led, and a paid long weekend tour I took back in 2009, it’s been me at the front. When Mark suggested we go on a ride that he would lead and on roads I’d not been on, well, my interest was piqued. The route was planned to be scenic along several smaller level cols, and very much a “bimble” rather than a thrash, one to enjoy the sights on.

    This morning we’re back on the Thoiry bypass again, riding back through the covered orchards towards Clarafond I’d taken earlier in the week on my TT route ride, and from there dropping down to Seyssel and heading out towards Belley.

    At Culoz we head on over the roundabout instead of going right to Belley, and take the parallel road on the other side of the river before stopping for coffee in the picturesque villlage of Chanaz, which nestles below a hill alongside the river which had frequent pleasure boats on it even at this time of the morning.

    P1060077

    b97c0b63-5102-4e6f-bae5-748f8d889773(1)

    The road winds alongside the river for a while before we start on a myriad of smaller cols such as the Col Mont Tournier; Col du Lievre and Col de Lattaz; before ending up at the Col de L’Epine and these fabulous views over Lac Aiguebelette.

    P1060091

    P1060092

    P1060086

    Marks definition of the route as one to bimble on and enjoy was pretty accurate, impossible to go quickly on any of the small cols but with the occasional blast on some wider gorge roads, we were enjoying ourselves and around 12.30 we arrived in Corbel and the Aubege Thimelet where we enjoyed an excellent Charolais steak on the terrace outside.

    P1060103

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    The view from the terrace outside where we were eating reminded us a lot of the Italian Dolomites

    P1060106

     

    P1060098

     

    P1060104

     

    After lunch and more small cols and riding a winding gorge road in both directions, we decidied to visit the Cirque de Memes. There’s a €2 charge per bike to enter and shockingly we only had €2 between us in cash and they don’t take cards, so I ended up having to write a cheque for the €4 entry.

    Here’s what we found when we got there.

    P1060116

    Marks interminable photo taking

    P1060121

    But worth it for the result below.

    Cirque-Même_1(1)

    Back to my pics from my trusty Lumix point and shoot

    P1060125 - Copy (2)

    P1060129 - Copy (2)

    P1060130 - Copy

    After spending an hour or so at the waterfalls we headed back towards Chambery where Mark led us over the Col du Chat, but in all honesty I was gettting a little tired by then and would have enjoyed coming back along the low level roads rather than the 14kms of ascent and descent we had along tight switchbacks and gravel strewn roads. Anyway, at the top of the Mont du Chat you’re rewarded with these great views. The runway at Chambery airport can clearly be seen in the middle of the picture.

    P1060137

    P1060141

    P1060138

    We eventually got home after a long day having spent 7 hours 11 in the saddle and ridden 431 kms but yet again the bike had held up in 27C temps so looks like the cooling issue is ok, fingers crossed! Thanks to Mark for leading, although I have to say I found it weird to be following not in front setting the pace, but it was different, and as I started this piece by saying , variety is the spice of life.


  • True costs of running a K1300GT over 7 years

    yosemite_sam2-1-1[1]

     

     

     

     

     

     

    Over the years I’ve posted several times about my K1300GT, it’s performance and issues, but given the recent costs and issues I’ve had with it and after an article recently published in MCN saying that the K BMW bikes are practically disposable items due to high cost of repairs and depreciating values, I thought it would be of value to share with others my experiences regarding running costs and residual values, ie the true monetary outlay required to keep it on the road. I’ve not included costs for insurance or petrol as these will vary massively dependant on the rider, their experience and where they live, neither have I included petrol expenses, although with the bike averaging 50mpg over 56,000 miles, a simple calculation shows that  I would have used around 1120 gallons.

    I’ve also not included around €725 of extras I chose to add (including derestricting it) as these are very specific to my bike and others will be unlikely to add the same parts.

     

    Here then are the figures:

    Purchase cost new in July 2009                        €19500

    Owned 2556 days    Current kms 89,678  = ave 35 kms per day

     

    TYRES

    15 pairs of tyres: ave life front 7484 kms, rear 6387 kms

    TOTAL                                                              €3329

     

    SERVICING every 10,000kms – 8 to date costing €3071

    but next service due NOW with likely cost of €500

    TOTAL  (incl. 90,000 service due now)         €3571

     

    REPAIRS             

    Switchgear (L) at 70,000kms                               €343

    Switchgear (R) at 87,000kms                              €161

    Radiator overheating & oil leak

    at 88,000kms                                                       €457

    TOTAL                                                               €961            

     

    CONSUMABLES

     Battery at 73,000kms                                           €121

    Brake pads ( originals plus 2 replacement sets)   €295

    Air filters (2) at 40,000 and 83,000                         €73

    Clutch at 80,000                                                    €739

    TOTAL                                                               €1228

     

     

     

    GRAND TOTAL                                                €9089 equiv 47% of purchase cost

    Current book value                                              €8780

     Remaining value in bike today                           €1631 equiv 4.1% of purchase cost

     

    Daily running cost equiv.                                        €3.56

    Running cost per km                                              €0.10

     

    Looking at the book resale values it would have been better had I sold it in 2012 after 3 years of ownership as at that time it would still have retained 75% of its value. After 4 years that drops to 68% then plummets after year 5 down to 55%, although in years 5,6 and 7, annual depreciation has droopped to just a few hundred euros per year compared to the €3000 it lost in year 4. I should also quantify my specific bikes value which is around €500 less than bikes which would have covered only 10000kms p.a, mine has done nearly 13,000 and is valued accordingly.

    Looking at the costs above it seems that the repair element is pretty low with the bulk of these costs taken up by switchgear replacements which BMW declined to assist me with despite me writing to them and complaining. They replied that the bike had been out of warranty since 2011 (only 2 years given in France) and had high miles, however should I choose to buy another new or used bike from their dealers within the next year they will look sympathetically towards the cost of that purchase or trade in.

    The bike has been run without extended warranty and has had the suspension relay brace recall, one set of switchgear, an ECU and two rear driveshaft bearings replaced under warranty.

    I leave you to make what you will of the above, clearly any future costs could potentially be high, the ESA suspension and driveshaft are a worry and I know others with lower mileage bikes have already had these replaced.

    My view is that the more you ride these bikes the better they perform and the less problems you have, keeping one as a weekend toy may keep daily running costs down but parts may not react well to being stood for long periods. I rode mine 1161kms within 3 days, 2090 within 7, 5140 in 28 days and 9091 within 60, not the norm by any means but its been ridden long and hard with huge amounts of time in the mountains in low gears driving out of hairpins so overall I reckon it’s not done too badly, trouble is I haven’t found anything I’d like to replace it with so maybe I just have to steel myself to potentially big future bills and run it into the ground, after all, don’t we buy these bikes expecting trouble free reliability and big mileages?


  • The TT route revisited

    yosemite_sam2-1-1[1]

     

     

     

     

     

     

    Having survived a full days ride without bike issues, Mark and I started planning another days riding. A check on the forecast though showed that tomorrows weather was bringing potentially severe storms which put paid to the idea of a full days ride, so we agreed to postpone until later in the week. I reckoned though, that I could probably get round one of my favourite rides, the TT route in 4 hours, but with the storms which had been forecast as due at 14.00 now changed to midday and possibly even 11.00, I’d need to leave very early.

    The next morning mindful of the coming storms, I was up early, had breakfast, and was dressed and had fired up the GT and had set off at 06.21am. Within 50 metres the bike decided to play it’s occasional game of flashing up a lights out warning symbol. Knowing that the garage had just replaced a bulb I stopped, switched everything off, restarted the bike, checked the lights, and lo and behold all was working. Scare over, it was time to get going.

    The autoroute is less than one minute from the house, I joined it and 13 minutes later a bunch of sequential numbers appeared on the dash, all the 8’s, 88,888 marking advanced age and even more kms  on the battle bus.

    It’s 18C even this early in the morning but already commuters are heading into Geneva from Lausanne, and I’m amused how aggressively someone in a small red Honda is trying to overtake the small red Citroen in front of him, often times speeding up the inside lane trying to undertake it. Must be keen to get to work!

    Soon I’m passing through the unmanned douane at Ferney Voltaire and passing Prevessin en route to the roundabout near Cern, before joining the Thoiry bypass. I’m careful to keep to the 110 speed limit as there are often radars along this stretch of road, but not today, it’s too early for the police to be about and besides, most of the traffic is heading into Geneva not away from it as I’m doing. Many many years ago I maxxed out my Honda Blackbird on this stretch of road, but that was LONG before radars were placed on it. There are plenty of buzzards flying overhead this morning, shame Sue’s not with me this morning as she loves watching them, but she preferred to stay and catch upon some sleep, so I watch as they soar above.

    We had been diverted en route to Bellegarde on Saturdays ride, so today I take the diversion signs crossing the river, and then turn right through the rows of orchards beneath their gossamer like covers, and head toward the viewing point of Fort L’Ecluse, but today I’m taking pictures of the valley back towards Geneva not the fort.

    P1060058

    The road has been resurfaced along some of this stretch and I’m enjoying the smooth tarmac until it ends and I’m faced with my least favourite obstacle, tar snakes. Superman had kryptonite, I have tar snakes. Faced with these demonic slivers of raised tarmac I become fixated by their positioning and take all sorts of bizarre lines to avoid them. Years ago I had a really bad ride on country roads where the whole surface seemed to be these snakes. The bike slipping and sliding so badly I thought I’d got a puncture. Stopping several times to check the tyre pressures, eventually I realised it was the tar snakes, and even though some years later a fellow rider tried to assuage my issues by deliberately accelerating over them to show it was safe, I have never got over been massively unnerved by them, maybe some therapy or hypnosis might help?

    Passing through Clarafond I join the main road dropping down into Bellegarde, skirt around the city and soon join the road out towards Chatillon en Michaille and the start of the my favourite stretch of road. This section to Nantua is the same as we’d ridden on Saturday, but as it has a sequence of some of my favourite bends I’m not complaining.

    In Nantua the diversions are still in place but this time I know the drill and am soon out the other side of town and passing alongside the lake out of town. At the roundabout I turn left, then it’s off to the Gorges du Cerdon around 10 minutes up the road  More great bends and well surfaced, it’s a blast to have the roads almost to myself, and descending the gorges I decide to go back and take some pictures, but not until I’ve taken this one at the bottom.

    P1060062

     

    For probably 7 years I rode down this road passing the statue at the bottom, and one day when I asked my riding buddies about the statue, not one of them had noticed it!! A quick blast half way back up for these pictures then it’s off again.

     

    P1060066

     

    P1060065

    The next stretch is a boring transition but only takes about 10 minutes before it’s back to the good stuff again and the amazing stretch from Les Hopiteaux to Piegeu. There’s a right hand bend nearing Belley that even at 160kph (alledgedly) goes on for 20 seconds. Once I was leading a group of 4 and we took this bend at 120 (alledgedly), only to be followed by a police motorcyclist who had been manning a radar on a layby on the other side of the road. Luckily as we’d been riding closely together he couldn’t register individual speeds so we got let off with a little “chat”, amazing bend though!!!.

    Knowing the storms were coming I resisted the option to stop at McDonalds near Belley and kept going, stopping only to take these shots. The first near Belley and the second two looking across to the Jura near Clarafond.

    P1060069

    P1060071

    P1060072

     

    The return leg was uneventful and an hour and a half later I was back with the GPS showing EXACTLY four hours riding time. Skip back to the first paragraph and you’ll see my estimated time to get round had been 4 hours, am I good or what?!

    So another great circuit ridden and another 328kms covered without cooling problems. With just the faulty light out reading which I hope I can clear with a GS-911 tool, hopefully there will be some days to come where I’ll have a fuss free ride!

     


  • Tentative first ride after radiator problems

    yosemite_sam2-1-1[1]

     

    15 or so years of riding Japanese bikes has shown me that it’s possible to turn the key in the ignition every day, have the engine start, and ride for tens of thousands of miles without breaking down, if faults existed they were relatively minor, and looking back on my riding history (perhaps through rose tinted glasses) I don’t remember too many issues with whichever Kawasaki, Suzuki, and Honda I’ve owned. I’ll admit that there was the well known regulator/rectifier fault on the Hondas, but they’re known for it and it’s almost an acceptable fault as nothing else goes wrong. My R1 had a TPS fault but didn’t actually break down, and only my beloved RC 45 left me needing a trailer ride home after its regulator failed, but these were all isolated incidences and NOTHING else ever went wrong, it’s only the BMW’s I’ve owned that have managed to leave me stranded, and on more than one occasion.

    The first breakdown came on a K1200GT demonstrator I bought from a dealer. BMW saw fit to create an electrically assisted braking system, which whilst being boosted by battery assistance, suffered the fate that if the battery started to discharge in stop start traffic with constant braking, it would fail, as happened to me on a trip to Luxembourg in motorway roadworks. Strike 1.

    Strike 2 came within 3moths of the purchase of a brand new K1300GT which replaced the K1200GT, when the ECU failed.

    In fact there have been several occasions over the past couple of years, notably at altitude and in very hot weather, when the bike has refused to start or needed bump starting, culminating in various changes of switchgear (at no small cost) and a lot of inconvenience. A booster plug helped the poor running, but combine this with driveshaft bearings which self destruct every 30,000kms, and you’re probably wondering why I’m still riding the GT, especially after the latest overheating problem?

    I guess it’s because I don’t actually know what I’d replace it with, and probably because after having ridden it for the past 7 years in restricted 100bhp mode I’d quite like to enjoy the full fat 160bhp it has now it has been derestricted. In truth I’m a little worried about the impact of suddenly having an extra 60bhp on an engine that has had such an easy life with only 100bhp for so long, but for now I’ve got a sickly machine that may or may not be ok after its overheating incident, so all I can do is ride it and find out, so here’s what happened after its first ride after having been side lined with radiator problems.

    It’s the day after I collected the bike from the dealer, and Mark and I have decided to do a relatively local ride on some of my favourite roads. The distance won’t be so great that if there are issues it will take a day to get trailered back home, but will be far enough to enjoy. Planning to arrive at Marks at 10.00am we arrive as the clock strikes the hour. Marks K1600GT is warming up and we’re soon off, stopping at the petrol station at the local supermarket. Signs warning of a diversion to Bellegarde suggest we take a different route, but we continued on past Fort L’Ecluse and the winding road to Bellegarde, which we can enjoy as it has very little traffic on it this morning. 5kms outside Bellegarde we reach the roadworks and diversion onto small backroads as a sign indicates the road ahead is closed for roadworks until April 2017!

    Eventually we end up on the outskirts of Bellegarde and joining the road we want to take towards Chatillon en Michaille, and from there onwards to Nantua. There are some great sequences of bends on this route, and overtaking any cars ahead of me I’m able to get maximum enjoyment of them.

    In Nantua there are yet more diversions. It’s summer so the French are digging up the roads and sending you on badly signposted diversions to wherever they think you might want to go. We stopped so I could mount the GoPro before climbing the TT hill coming out of Thoirette . This hill has a great surface, great bends, takes two minutes to ascend even flat out, and you only need to back off slightly for two corners until you reach the top and the great viewing point there.

    Strangely, given it’s mid season, our target restaurant at Pont Le Pyle is closed, but there are others close by, and after a jambon/fromage sandwich, coke and ice cream have been consumed, we’re off again, this time Mark leading, with the destination being the Source du Lison, which he tells me was full to overflowing last time he visited a couple of weeks earlier. I should have known better than to believe it when he told me he knew the way though, as 25 minutes later we are arriving at Lizon (spelt with a Z ) not in Salins where we should be to see the Lison, neverthless the sun is shining, we’ve got all day, and at the moment the GT isn’t showing any signs of repeating it’s overheating issues, despite the warm temperatures.

    An hour or so later and after some searching around due to poor signposting, we eventually arrived at our destination, where the source of the river Loue has it’s  origin. It’s hot though, so our first call is the cafe by the side of the river for a couple of refreshing drinks before the short walk to the water gushing from the hillside.

    P1060023

     

    P1060027

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    Here’s one of Marks shots using a “proper” camera

    Source-LISON_ 1_10_07_16

     

    P1060030

     

     

     

     

     

     

    P1060032

     

    P1060033

     

    P1060036

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    Here’s a picture of Mark and his super expensive camera which he spent forever composing shots with. Apparently he take lots of the same shots but on different settings, and then manipulates them in Photoshop. Check out picture 3 above

    P1060038

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    After seemingly hours waiting for Mark to compose his pictures, we decided that as it’s still only late afternoon, we’d take advantage of the opportunity of having Mark  show us somewhere we’d not been before, the Cascades du Tuf, which are on the way back anyway, so off we shouldn’t have any navigational problems getting there?

    Parking the bikes up later the 300m uphill walk is an efffort in the heat, but here’s the waterfalls at the top.

    P1060039

     

    P1060047

     

    P1060048

    We couldn’t help noticing how much this tree stump looked like a rabbit

    P1060052

     

    P1060053

    P1060054

     

    After cooling off in the shade whilst Marks 5 minutes of photo taking took 20, it was eventually time to head for home. Mark having realised that he was due at his neighbours at 20.00 might just about make it back in time, but we decided to stop off in Champagnole for a McDonalds and toilet break. Later we decided to descend via Arzier rather than the 73 hairpin bends of St Cergue, and as we headed back down it was pleasant to see the evening sun setting over the Alps and Lac Leman.

    Arrtiving back at 21.15 with 518kms having been ridden, it had been a long day, but the bike had behaved and never got beyond 2 bars on the temperature gauge, so now I’m wondering whether I do actually need the new radiator the dealer wanted to sell me? I guess for now I’ll just keep riding it and see how things develop.


  • Is it still broken or fixed now?

    yosemite_sam2-1-1[1]

    Those of you who read my last post will know that the GT ended the day in disgrace after overheating and leaking oil during its last ride. With the following day being a Sunday and all bike shops being shut on Mondays, the earliest I was going to get it looked at by anyone would be Tuesday. Trying to get ahead of the game and salvage some riding time for the following week I sent an email to the garage I’d bought the bike from in Annecy, asking if I could take it in on the Tuesday. The shop there opened at 09.00 but I had a sceond option, which was to contact the local Swiss dealer in Crissier which was open at 08.00. Given the fact the Swiss shop was only 20 minutes away, I decided that I’d be better off paying higher Swiss labour prices than dragging the bike over an hour and a half away to the French dealer, so I phoned the Swiss shop as soon as they opened in the hope that they’d make a big effort to help a touring motorcyclist in trouble. Unfortunately when I rang the shop was full of riders booking in their bikes for services so I was asked to call back later. When I finally got through I managed to persuade them to take the bike in although they wouldn’t commit to when it might be looked at or returned. This turned out to have been the best option though, as by 11.00 the bike had been booked in, faults explained and left there, whilst the French dealer took until 14.15 that afternoon to write back saying bring it over and they’d look at it, but if it needed any work doing they didn’t have the time! No use whatsoever and a pretty poor response to an email which had been entitled URGENT, still, the bike was booked in now and all I could do was wait.

    Wednesday passed with no news, so when I’d still heard nothing by 10.00 on Thursday I figured they must at least know by now what was wrong regardless of whether it had been fixed or not, so I rang again. The radiator had been diagnosed as being clogged internally and I was quoted a price for fitting a new one of 750chf. Add to that the oil leak repair and the total bill was looking to be around 1300chf, not exactly a cheap fix. I was told if I confirmed the order within the hour there was a chance the part would be delivered and fitted for Saturday but I had to make a quick decision. I hopped in the car, drove to the garage and interrogated the service guy as to whether flushing the system would clear the issue, but he was less than positive about the success of that option. Unfortunately for me I didn’t have the cash immediately available for such a big repair, so I decided to get them to refill the system so that I could at least ride it back to the house and then trailer it back home to get it repaired at some future date. Although the oil leak hadn’t been fully diagnosed it was likely to be a simple fix, so it was agreed that on Friday I would return to collect it and take it away in the best condition it could be returned in, without the fitment of a new radiator.

    Friday came along with a bill for 497chf. The oil leak had been traced to a bolt which seemed not to have been tightened properly when the clutch had been replaced, although this had been almost two years earlier at 80,000 kms.  Perhaps the overheating had exacerbated the problem and caused the gasket to leak some 8000kms later, who knows?

    The radiator had been pressure tested, purged, and refilled with coolant. I was told it was unlikely to blow up but to watch how it performed under load as they couldn’t guarantee the problem wouldn’t resurface again and for sure it wouldn’t get any better, so I had the bike back but with no idea how reliable it may be in the future.

    The 20 minute ride back showed the coolant level at the “normal” levels, but as it was getting motorway speed air blasting through to keep it cool and wasn’t under any load in slow moving traffic or at altitude, it wasn’t really any indicator of how it might perform in the future, so I’m left with no option other then to take it for a “proper” ride later in the week and see what happens, so as per the ending of the last post, watch this space for the latest.


  • And it all started so well!

     

    yosemite_sam2-1-1[1]

    Since moving to the Dordogne from the Geneva area in Switzerland, one of the things that I’ve missed the most has been the mountains. One year I rode 28,000kms researching and leading my tours there, and there is nothing like the thrill of riding at altitude and enjoying hundreds of switchback hairpins and taking in the magnificent views.

    An opportunity arose to return and ride in the area for a few days, but rather than ride 7 hours back to the region, I cheated and trailered the bike there with a plan to ride a few big passes and lots of the smaller local ones I’d ridden in the 12 years I’d lived there. Surviving the traumas of loading a 285kg bike onto a trailer the journey had been hassle free, other than finding the tie down strap I use on the rear wheel wouldn’t fit around the bazooka of an exhaust, so I had to swing it out and bolt it in an outward hanging position to allow me to secure the wheel in place.

    Andy was to be my partner on the first of my planned rides, a very full days ride from Geneva to Grenoble, down the famous route Napoleon to Gap, across to Briancon, then over the Col du Mt Cenis (2081m) and then back via the Col D’Iseran ( 2770m) in France. It’s a big day with big distance and altitudes, but with a forecast showing at least 22C, the 6.00am wake up was an acceptable necessity, and at 07.25 we were at Andys and ready to go. Leaving his house takes us immediately past a view across Lac Leman where Mt Blanc was beautifully lit by the early morning sun. It may only have been 12.5C but the view was magnificent and a great start to the day.

    Next a stop off in Divonne for petrol and then we’re off onto the first leg of the journey via the peage down to Grenoble. It’s circa two hours down to the services we always stop at to break the journey, and despite it being all autoroute there is plenty to see and sights to take in, especially as we near Grenoble and the mountainous terrain begins. Low clouds shrouding the hills is always atmospheric, buzzards circled above, riders on road bikes were out in their early morning Tour de France  peletons, and runners jogging through the countryside were all interesting diversions.

    The temperature raised to a balmy 18C as we got further south although it was windy, the occasional wind sock blowing at 90 degrees showing how breezy it was. The GT has a big screen to hide behind though and other than the wind hitting the topbox and wagging the tail from time to time, it was no big deal. Andy is able to fly through the peage booths with his prepaid toll badge whereas we continue our “normal” routine of always managing to choose the lane where someone either has no money, or hasn’t driven on peage motorways and doesn’t know what to do, or is just slow. Nevertheless we arrived at our first stop off, the Aire du Bois Claret without any drama and filled up for the next leg down the Route Napoleon to Gap.

    I don’t often take the N85, much preferring the far prettier and more flowing (in my opinion) N75 which runs parallel to it, but taking this route would have meant riding back East to Gap which would have added unnecessary time and mileage. Being a Sunday the road wasn’t too busy so we made good progress and in Gap took the road to Briancon which crosses the gorgeous Lac de Serre Poncon. Today the lake was nothing short of magnificent, it’s water levels at  close to maximum and a stunning turquoise blue in the sunshine. There is a  little church on a tiny island there which reminded me of a much bigger version in Lake Bled in Slovenia. Crossing the bridge and passing the restaurant we often stopped at, today we are continuing on instead of turning right and taking the lakeside road, signposts showing Briancon is  77kms from here.

    As we crawled though the town of Briancon and up the steep hill out of it, I noticed that the water temperature suddenly went sky high. Cursing the slow moving traffic I had grave concerns the bike would overheat, and as soon as we got to open roads had to speed up to try and get some fresh air through the radiator to cool it down. That was fine when the roads were flat, but as we started to climb the steep ascent towards Montgenevre we got caught behind cars now and again and the bar graph temperature gauge started its inexorable trip upwards towards the danger zone. There was nothing I could do, we weren’t moving fast enough to get enough air through to cool it, and rounding a bend the red warning triangle illuminated and there was no option other than to pull over and hope it would cool down. I couldn’t hear the fan running whether the engine was switched on or not, so it was looking like there was an issue which would doubtless continue throughout the day. After a 10 minute break the temperature had dropped a little, and with the town just 2 minutes up the road we decided to stop for lunch, leaving the bike parked in the shade and hoping it would cool down sufficiently to allow a trouble free afternoon, although deep down I knew that was going to be unlikely.

    The lunch break over, we attached cameras, and now it’s really clear we’re in Italy, as from here on in the Italians started to appear in numbers, always riding fast and in smart leathers, even a group of 4 riders on Yamaha T Max scooters were riding quickly in formation ignoring the 70 speed limits, so as they say, when in…….

    Arriving at the outskirts of Oulx we got diverted around the town due to some river event but soon found the correct route and passed a huge old abbey en route to Susa. The temperature gauge had been hovering around the 2 bar mark for most of the time. One and a half bars is “normal” but with temperatures at 22-24C I wasn’t too worried until we arrived at Susa and had to wait at traffic lights and then ride slowly through the town centre. Starting the climb out of the town and looking forward to the climb up the Col du Mt Cenis it wasn’t long until I realised things weren’t going well. Just a few minutes later and the gauge was at the top of the scale and the red warning light was back on again, leaving me no choice other than to pull over and let it cool down again. At this stage I’m feeling like Basil Faulty when he thrashed his car with a branch, the best I can do however is throw my gloves at it in disgust as clearly today isn’t going to go as planned, and just to make matters worse, there is oil leaking from the clutch cover seal. Crap!!!

    IMG_1064

     

    Another enforced cooling down period and the plan is to ride on keeping speeds and rpms low and then head back for home via the motorway, where at least higher speeds will keep the engine cool. The Col du Mt Cenis isn’t as much fun at lower speeds, but other than getting stuck behind a few cars towards the top I’m able to keep the temperature down, and soon there is just the descent towards Lanslebourg to manage, although I’m not particularly keen on this bit of road and the gauge is firmly on the two bar mark, so what with concentrating on that I’m not actually riding too well.

    At Modane we fill up again, join the peage and start the journey back towards Chambery where the promise of a McFlurrys incentivises. Andy spotted the turn off into the centre commercial but we didn’t didn’t, necessitating a U turn through the parking at the peage toll a kilometre up the road to get back to him. Parking up I found that there was oil on both mine and Sues right side boots, on the frame and exhaust, and even the rear wheel and edge of the tyre, not good! The leak was clearly getting worse and later on I could actually see oil weeping from the seal. Luckily I always carry oil with me as the GT has had a habit of using oil every niow and then, so I topped up and hoped the leak wouldn’t get any worse.

    The peage back was covered circumspectly as I worried about both the oil and water temperature, but we made it back ok in the end after 728kms and just over 8 hours riding which had provided a mix of enjoyment of riding great roads, but also frustration at the bikes issues. It was a shame to have had to cut the route short and that Andy had ended up having to ride shotgun for an ailing GT, but at least we’d had a runout.

    In an odd co-incidence, a few days earlier a guy had written to me asking for my opinion on the long term reliability of the K1300GT as he had been thinking of buying one. I’m not sure what to tell him, I guess it will depend on what the problem is and how much it costs to fix it!

    Watch this space for an update.